oxidation loss
英 [ˌɒksɪˈdeɪʃn lɒs]
美 [ˌɑːksɪˈdeɪʃn lɔːs]
网络 氧化损耗; 氧化烧损; 氧化損耗
双语例句
- Evaluation of the fired samples for oxidation percentage, weight loss, dense zone and microstructural characteristics of the zone is carried out.
对煅烧后的试样的氧化百分率、失重、致密层和致密层的显微结构特点作了鉴定。 - Research on oxidation kinetics model of coal based on carbon element loss rate
基于失碳速率的煤氧化动力学模型研究 - The oxidation weight loss rate of binderless C/ C composite prepared by in situ carbonization of pre oxidized fibres ( PAN) was tested in the air, at 0.1 MPa, from 673 K to 973 K using thermo weight analysis method.
采用恒温热重法测定了在空气中，0.1MPa、673K到973K下预氧丝（即预氧化聚丙烯腈纤维）原位炭化无粘结剂C/C复合材料的氧化失重率； - As a result, the heating capacity and quality of heating furnace is improved, the slab surface oxidation burning loss is decreased and the gas consumption reduced and the economic benefit remarkable.
改造后使加热炉提高了加热能力和加热质量，减少了板坯表面氧化烧损，降低了煤气消耗，经济效益显著。 - Controlled cooling after rolling is widely used in high speed wire production line. Compared with natural cooling, it can not only improve cooling rate and reduce oxidation loss, but also guarantee the product quality.
高速线材的轧后控制冷却工艺，与轧后自然冷却相比，不仅可以提高冷却速度，减少氧化损耗，而且可以保证产品质量，因此得到广泛应用。 - It can intensify a lot of properties of iron and steel in corrosion resistance, resistance to heat and oxidation resistance at high temperature, decrease the economic loss by corrosion and abrasion, prolong the life of ferrous products greatly and bring good benefits.
钢铁渗铝后可以增强其耐腐蚀、耐热及抗高温氧化等诸多性能从而大大的减少钢铁因锈蚀和磨损等造成的经济损失，延长钢铁件的使用寿命，提高经济效益。 - The wear rate of pin specimens without electric current shows a monotone increase with an increase in electric current. The wear mechanism is mainly attributed to adhesion and abrasion, oxidation and electric arc ablation loss.
有电流时，销试样的磨损率随电流的增加而增加，其摩擦面上有电弧烧蚀坑，同时伴有磨粒磨损，粘着磨损和氧化磨损。 - The XRD, SEM analysis, the oxidation weigh loss and annealing circulation experiment with the coating are done.
对涂层进行了XRD、SEM分析、氧化失重实验和热循环实验。 - Reasons of oxidation burning loss to heating furnace and its countermeasures
加热炉氧化烧损原因与对策分析 - The melting temperature is lower, which is bad for the display of flux, while the solubility of hydrogen is increased and the oxidation loss of the component is intensified if the melting temperature is higher, so the melting temperature will be appropriate;
熔炼温度过低，不利于熔剂作用的发挥。熔炼温度越高，氢的溶解度将随之增加，加剧了组元的氧化烧损，熔炼温度要适宜；